How to Change Blades on Zero Turn Mower?

To change the blades on a zero turn mower, first locate the bolts that hold the blade in place. Next, use a wrench to loosen the bolts and remove the old blade. Finally, install the new blade and tighten the bolts back down.

  • Park the mower on a level surface and turn off the engine
  • Raise the deck of the mower to its highest position
  • Remove the bolts that hold the blade in place with a socket wrench or impact driver
  • Take off the old blade and put on the new one, making sure it is installed correctly
  • Tighten the bolts holding the blade in place, then lower the deck back down to its original position
How to Change Blades on Zero Turn Mower?

Credit: upgradedhome.com

How Do You Take Blades off a Zero Turn Mower?

When it comes to taking the blades off of a zero turn mower, there are a few things that you will need to keep in mind. First, you will need to make sure that the engine is turned off and that the spark plug is disconnected. Next, you will need to remove the mower deck by loosening the bolts that hold it in place.

Once the deck is removed, you will be able to access the blades. In order to remove the blades, you will need to unbolt them from the spindle. Once they are unbolted, you can simply pull them off of the spindle and set them aside.

How Do You Change a Zero Turn Blade Without a Jack?

Assuming you have a John Deere Ztrak Zero Turn mower, the process for changing the blades is as follows:

You May Also Like:  How Long After Overseeding Can I Apply Weed And Feed?
1. Park the mower on a level surface and turn off the engine. Disengage the blade control levers, then set the parking brake and remove the key from the ignition.

2. Place blocks under each side of the deck to keep it from tipping over while you’re working on it. Make sure the blocks are high enough that they won’t touch the ground when you lower the deck. 3. Use a socket wrench to remove the bolts that hold each blade in place.

There are usually three bolts per blade. Set the old blades aside and put on your new ones, making sure they’re tight before moving on. 4. Reattach all of your safety devices before starting up your mower again, and be extra careful when backing it out of its blocking situation – those blocks will still be there!

How Do You Jack Up a Zero Turn?

To jack up a zero turn mower, you will need to use a jack that is rated for the weight of your mower. Place the jack under the front of the mower deck, near the center. Slowly lift the jack until the wheels are off the ground.

You may need to adjust the jack to get it into position. Once the wheels are off the ground, you can move the mower around as needed.

How Often Should You Change Blades on Zero Turn Mower?

It is important to keep the blades on your zero turn mower sharpened and replaced as needed in order to maintain a healthy lawn. Depending on how often you use your mower and the type of grass you have, you will need to change your blades anywhere from every few weeks to every few months. A good rule of thumb is to inspect your blades after each mowing session and replace them when they become dull or damaged.

You May Also Like:  How Long are 8D Nails?

how to change the blades on a zero turn mower or riding mower

Conclusion

It’s important to keep your zero turn mower blades sharp so that you can get a clean cut and avoid damaging your lawn. Fortunately, changing the blades on a zero turn mower is a relatively simple process that you can do yourself. Here’s how to do it:

1. Park your mower on a level surface and shut off the engine. Remove the key from the ignition to prevent accidental starting. 2. Disengage the blade control lever or switch so that the blades will not start spinning when you restart the engine.

3. Raise the deck of the mower so that you have easy access to the blades. On most models, you can do this by simply pulling a lever or knob located near the seat. 4. Use a wrench or socket to loosen and remove the bolts that secure each blade in place.

Be sure to hold onto the blade with one hand as you remove it so that it doesn’t fall and become damaged. 5a) If you’re only replacing one blade, skip to step 6). Otherwise, continue with step 5b).

5b) Inspect both blades for damage such as nicks, cracks, or warped edges. If either blade is damaged beyond repair, replace it with a new one (available at most hardware stores). Otherwise, proceed to step 6).

6) Place each new or sharpened blade back onto its spindle, making sure that it is positioned correctly (consult your owner’s manual if necessary). 7) Using your wrench or socket, tighten each bolt securely but be careful not to overtighten as this could strip the threads or damage the spindle itself.