Turn the dustbin over and press the release button to open the door. The debris will fall out into your hand. If there is any stubborn dirt, use a small brush to remove it.
- Open the top lid of the Roborock dustbin
- Remove the filter from inside the lid
- Take out the dustbin and empty it into a garbage can
- Replace the filter and close the lid
Contents
How to Empty Roborock S7 Dustbin
If your Roborock S7 is anything like mine, then it’s probably full of dust and debris. Here’s how to empty it out:
1. First, remove the dustbin from the vacuum by pressing the release button and lifting it out.
2. Next, take the filter out of the dustbin and tap it against a hard surface to remove any loose dirt.
3. Now, holding the dustbin upside down, press the release button again and open up the bottom panel. Doing this will allow all the collected dirt and debris to fall out.
4. Finally, give the inside of the dustbin a good wipe down with a damp cloth before putting everything back together and reattaching it to your vacuum cleaner.
Credit: www.amazon.com
How Do You Empty the Dust Bin on a Roborock?
If your Roborock is like most models, there will be a release button on the bottom of the unit. Press and hold this button while tipping the vacuum cleaner upside down over a trash can. The bin should release and the debris should fall out.
You may need to shake the unit slightly to get everything out.
How Do I Manually Empty Roborock S7?
If you need to manually empty your Roborock S7, the first thing you’ll need to do is locate the dustbin. The dustbin is located on the back of the unit, near the bottom. Once you’ve found it, simply press and hold the release button for 3 seconds.
This will open the door and allow you access to the dustbin.
With the filter removed, hold the dustbin over a trash can and press down on the release button again. This will cause the bottom of the dustbin to open up, allowing all of the dirt and debris inside to fall out. Give it a good shake if needed to get everything out.
Once everything has been emptied out, replace both filters (make sure they’re firmly in place) and close up both doors. Your Roborock S7 is now ready to continue cleaning!
How Do You Empty the Water on a Roborock S7?
Assuming you would like tips on how to effectively empty the water tank on a Roborock S7:
First and foremost, it is important to ensure that the water tank is completely dry before attempting to remove it. To do this, simply leave the tank out in the sun for a few hours or use a hair dryer on its lowest setting.
Once the tank is dry, unscrew the cap at the top and carefully pour out any remaining water. Be sure to check the bottom of the tank for any leftover water as well.
Next, if your Roborock S7 has a filter, remove it and rinse it off with clean water.
If possible, let it air dry or pat it down with a clean towel before putting it back in place. If your vacuum does not have a filter, simply skip this step.
With both the filter and water tank taken care of, reattach them to your Roborock S7 and you should be all set!
How Often Do You Need to Empty Roborock?
Assuming you are talking about the Roborock S5 robot vacuum, it has a dustbin capacity of 0.48L. That means if you have a relatively clean home, you can expect to empty the dustbin every 1-2 weeks. However, if your home is on the dirtier side, you may need to empty it more often – perhaps once a week or so.
Roborock S5 — Cleaning Dust Bin and Strainer
Conclusion
If your Roborock vacuum cleaner is full of dirt and debris, you may be wondering how to empty the dustbin. Here are some simple instructions on how to do just that. First, remove the dustbin from the vacuum cleaner.
Next, open up the dustbin lid and dump out the contents into a trash can or other suitable container. Be sure to dispose of the debris properly so that it does not end up back in your home. Finally, wash out the dustbin with soap and water (or vinegar and water for a natural cleaning solution) and allow it to dry before putting it back on your vacuum cleaner.