1. Unplug the Ryobi 40V weed eater from the power source.
2. Remove the spool of string from the weed eater.
3. Cut off a length of string that is about twice as long as the original spool of string.
4. Feed one end of the string through the eyelet at the bottom of the spool, and then tie a knot to secure it in place.
5. Wind the string around the spool in a clockwise direction until there is about 6 inches of string remaining.
6. Feed the remaining end of the string through the other eyelet at the top of the spool, and then tie another knot to secure it in place.
- Pull the spool out of the Ryobi 40V weed eater
- Cut the old string off of the spool
- wind the new string around the spool in a clockwise direction
- feed the end of the string through the eyelet on the side of the spool
- continue winding until you have about 6 inches of string left
- cut the string and tie it off to secure it in place
- insert the spool back into the weed eater and you’re ready to go!
Contents
Ryobi Expand It 40V Electric String Trimmer Line Replacement
How Do You Put String in a 40V Ryobi Weed Eater?
Assuming you would like a step-by-step guide on how to replace the string on a 40v Ryobi weed eater:
1. Start by disconnecting the power source from the weed eater. If it is battery operated, remove the battery.
If it is corded, unplug it from the outlet.
2. Next, use a Phillips screwdriver to remove the screws that are holding the spool cover in place. With the cover off, you should be able to see the spool of string inside.
3. Take out any old or damaged string from the spool and dispose of it properly.
4. To add new string, start by threading one end through the eyelet at the bottom of the spool (this is usually marked with an “IN” sign). Then, wind the string around the spool in a clockwise direction until there is about 6 inches of slack.
5 Trim off any excess string with scissors and reattach the spool cover using your screwdriver.
6 Finally, reconnect your power source and test out your newly strung weed eater!
How Do You Restring a Ryobi 40V Lithium?
If you’re like most people, you probably don’t think about the condition of your Ryobi 40v lithium string trimmer until it’s too late. The good news is that it’s easy to restring a Ryobi 40v lithium, and this guide will show you how.
First, remove the old string from the spool.
To do this, simply unscrew the spool cap and pull the string out. Next, cut off any frayed or damaged sections of the string using a sharp pair of scissors.
Start by threading one end of the string through the eyelet on the spool. Then wind the string around the spool in a clockwise direction until you’ve reached your desired length. Finally, screw on the spool cap and give it a few turns to secure it in place.
That’s all there is to it! Restringing your Ryobi 40v lithium is quick and easy, and it will keep your trimmer running smoothly for years to come.
How Restring Ryobi Weed Eater?
Assuming you would like a blog post discussing how to restring a Ryobi weed eater:
“How to Restring Your Ryobi Weed Eater”
Over time, the string on your Ryobi weed eater will become frayed and worn down, making it less effective at cutting through weeds.
When this happens, it’s time to restring the weed eater. While this may seem like a daunting task, it’s actually quite simple and only takes a few minutes. Here’s how to do it:
First, remove the spool of string from the weed eater. To do this, unscrew the cap located at the top of the spool and then pull out the spool. Next, cut off any remaining string that is attached to the spool.
Now take your new string and thread it through the eyelet located at the end of the spool. Then wind the string around the spool in a clockwise direction until there are about six inches of string left sticking out.
Once you’ve done that, screw the cap back onto the spool and then insert it back into place in the weed eater.
Be sure to line up all ofthe notches onthe spool with those onthe housing before pushingitinto place. Finally, givethestringa few tugs to make sure thatit’ssecurely inplace before usingyourweed eateragain.
Credit: www.amazon.com
How to Replace String on Ryobi Expand-It Trimmer
If your Ryobi trimmer uses a string head, over time you will need to replace the string. This is a relatively easy process that anyone can do with just a few simple tools. Here’s how to replace string on Ryobi Expand-It trimmer heads.
First, you’ll need to remove the old string from the head. To do this, unscrew the knob at the top of the head (1). Then, pull out the spool of string (2).
Once the spool is removed, you can cut off any remaining string with scissors (3).
Next, you’ll need to thread new string through the head. Start by feeding one end of the string through the eyelet at the bottom of the head (4).
Then, wind the string around the spool in a clockwise direction until it’s fully wound (5). Finally, screw the knob back onto the top of the head (6) and pull onthestringto make sure it’s tight before using your trimmer again.
With just a few simple steps, you can easily replace worn-out string on your Ryobi Expand-It trimmer head.
How to Open Ryobi 40V Weed Wacker
If you have a Ryobi 40V weed wacker, you may be wondering how to open it. Here are the steps:
1. Find the opening at the top of the weed wacker.
This is usually located near the handle.
2. Insert a flathead screwdriver or another type of tool into the opening.
3. Turn the screwdriver or tool until you hear a clicking noise.
This indicates that the mechanism has been released and you can now open the weed wacker.
4. Lift up on the top part of the weed wacker to open it up and access the interior components.
Ryobi 40V String Trimmer Troubleshooting
If your Ryobi 40V string trimmer isn’t working properly, there are a few things you can do to troubleshoot it. First, check the battery to make sure it’s fully charged. If the battery is low, charge it for a few hours and then try again.
Next, check the trimmer head to see if the line is tangled or broken. If the line is tangled, use a pair of scissors to cut it free. If the line is broken, replace it with a new one.
Finally, check the area around the trimmer head for any obstructions that could be preventing the trimmer from working properly. Clear away any debris and try again.
If you’ve tried all of these troubleshooting tips and your Ryobi 40V string trimmer still isn’t working properly, contact customer service for assistance.
Conclusion
If you’re like most people, you probably don’t think about your weed eater until it stops working. Then you’re stuck with a frustratingly tangled mess of string. But don’t worry, we’re here to help.
In this blog post, we’ll show you how to quickly and easily restring your Ryobi 40V weed eater.
First, disconnect the battery and remove the spool cap. Then, cut off the old line and thread the new line through the eyelet on the spool.
Next, wind the new line around the spool in a clockwise direction until it’s snug but not too tight. Finally, replace the spool cap and reattach the battery.
And that’s it!
You should now be able to get back to trimming your lawn without any problems.